# EN 15085-5: What Inspection, Testing and Documentation Must Prove

Source: https://www.therness.com/blog/en-15085-5/
Language: en

![EN 15085-5: What Inspection, Testing and Documentation Must Prove](https://www.therness.com/assets/images/blog/2026-11-18-en-15085-5-hero.webp)

EN 15085-5 is the part of the railway welding standard that governs inspection, testing and documentation. What it asks for, how inspection classes change the extent of testing, and what an auditor opens first.

**Author:** Luca Santoro **Published:** 18 November 2026 **Reading time:** 9 min

- en-15085
- railway
- weld-inspection
- ndt
- documentation
- iso-standards

A railway weld is accepted twice: once when it is examined, and once when someone, years later, can show that the examination happened, that the joint it describes is the joint on the vehicle, and that the result was judged against the right requirement. The first is inspection. The second is documentation. In the EN 15085 series, both of them live in the same part — the one that most fabricators read last and are audited on first.

This article explains what that part asks for, how the inspection class of a joint changes the work behind it, and what a documentation file has to contain to survive an assessment.

## Key takeaways

- EN 15085-5 covers inspection, testing and documentation of welds on railway vehicles and components.
- The inspection class of a weld is set at design stage and decides how much testing the joint requires.
- Classification under the certification part of the series is a precondition, not evidence that inspection was done.
- An audit asks for a chain, not a folder: drawing, procedure, qualification, production record, examination result, acceptance decision.
- A file that cannot link a result to a specific joint fails the audit even when every examination was performed.
- Production data strengthens the chain by showing what each joint went through; it does not replace the examination the class requires.

## Where this part sits in the series

The EN 15085 series is built as a stack, and each part answers a different question. One part is about the manufacturer and its certification level. One classifies components by consequence of failure. One covers design and one covers production. The last covers what happens after the arc is off: examination, testing and the record that stays behind.

The five parts of the EN 15085 series as a chain: manufacturing requirement, classification, design, production, and inspection with documentation

The practical consequence of the split is often missed. A company can hold a valid certification for the component classes it builds and still fail an assessment on the joints, because the certification answers a question about the organisation while the inspection part answers a question about each weld. Those are audited differently, and by different people.

## What the inspection class of a joint changes

Railway welds are not all examined to the same depth, and they should not be. The inspection classes in this part of the series exist precisely to avoid that waste: a joint whose failure would put a vehicle at risk is examined far more thoroughly than one whose failure is a cosmetic nuisance.

Three things follow from the class assigned to a joint:

- **The extent of testing.** A higher class generally means a larger share of production is examined, and by methods that find internal imperfections rather than only surface ones.
- **Who may accept the result.** Acceptance is a judgement against a requirement, and the requirement comes from the drawing and the applicable quality level, not from what the examination happens to show.
- **What the record must prove.** A class that requires volumetric examination leaves a different trace in the file than one that requires a visual check: a report with a method, a qualified operator, a result and an acceptance decision.

The inspection class belongs to the joint drawing. When it is assigned late, in the workshop, it tends to be assigned by whoever is available and to look like whatever is convenient that week. That is one of the findings an auditor can make without looking at a single weld.

## The evidence chain an auditor follows

An assessment is not a search for a single missing document. It is a walk along a chain, and any link that does not connect stops the walk. In a rail fabrication that chain has six links, and each of them is produced by a different activity.

The evidence chain: each link must connect to the same joint identifier, or the file stops being an audit trail

The failure mode is almost always the same and almost never a missing document: a report exists, but it cannot be tied to the joint it refers to. A radiograph with a film number and no joint identity, a visual examination sheet signed per batch instead of per weld, a repair note attached to the wrong assembly. Everything is there, and the file still cannot prove anything.

## Which examination, for which joint

The choice of method is a technical decision driven by what you are trying to find, and the part of the series concerned with inspection does not invent it: it points at the industrial practice for each joint type.

- **Visual examination** stays first in every case. It finds geometry, alignment, surface-breaking imperfections and the consequences of a bad restart, and it is the only method that sees the joint as a whole.
- **Surface methods** — penetrant and magnetic particle — are used where surface-breaking imperfections matter and geometry interferes with a reliable visual judgement.
- **Volumetric methods** — radiography and ultrasonic testing, including phased array — are used where the class requires internal coverage. Each has blind spots fixed by geometry: radiography struggles with planar imperfections oriented along the beam, ultrasonic testing struggles with coarse or anisotropic material.

In practice the methods are combined, and the combination is what an auditor reads as evidence that the coverage intended by the class was actually achieved.

## What the documentation has to hold

Stripped of the standard’s structure, the file holds the answers to six questions. If any of them cannot be answered for a given joint, the joint is undocumented regardless of how much paper exists elsewhere.

1. **What was this joint required to be?** Drawing, weld type, dimensions, quality level, inspection class.
2. **How was it meant to be made?** The welding procedure, qualified, with the range of conditions it covers.
3. **Who was allowed to make it?** Welder or operator qualification, valid for the process and position used.
4. **What actually happened?** The production record: pass sequence, conditions, repair history, and — where a monitoring system exists — the recorded process trace for that weld.
5. **What was found?** Examination reports with method, extent, operator, result.
6. **What was decided?** Acceptance, rejection, repair, and the record of what was re-examined afterwards.

Before and after: the same joint documented as a pile of paper and as a connected record. The difference is not the amount of evidence, it is whether the links exist

The right-hand picture is not an argument for software. It is an argument for an identity: one joint, one key, and every piece of evidence attached to it. A workshop can build that with a paper traveller if the discipline holds. What it cannot do is improvise it after the question arrives.

## Where production data earns its place

A monitoring system on the cell records the temperature field and the process trace of each weld as it is made. That is not inspection, and it must never be presented as inspection: it does not find a lack of fusion, it does not measure a throat, and it cannot declare a joint acceptable.

What it does is supply the fourth link of the chain with something better than a memory. Instead of “made to procedure”, the file can say what this joint actually went through — the preheat it started from, the interpass range it stayed in, the cooling that followed — attached to the same identity as the examination report. When a joint is questioned a year later, that is the difference between reconstructing and consulting.

For rail work the value lands in two places. Repairs and rework become traceable: the joint that was re-examined was the joint that was re-made. And trending becomes possible: a heat-input drift on one joint family shows up in the process data before it shows up in a rejection.

## Related reading

- [EN 15085 certification levels CL1–CL4 and what auditors check](https://www.therness.com/blog/en-15085-railway-welding-certification-requirements-guide/)
- [Rolling stock welding: quality levels and how to monitor them](https://www.therness.com/blog/en-15085-rolling-stock-welding-quality-levels-monitoring-guide/)
- [Welding QMS software for ISO 3834, EN 1090 and ASME](https://www.therness.com/blog/welding-qms-software-iso-3834-en-1090-asme/)
- [Phased array ultrasonic testing for weld inspection](https://www.therness.com/blog/phased-array-ultrasonic-testing-paut-weld-inspection-guide/)
- [WPS: what a welding procedure specification must contain](https://www.therness.com/glossary/wps/)

### Give every rail weld a record that answers the audit question

Therness monitoring keeps the process trace of each weld next to the part, with the same joint identity the inspection report uses, so the file can be read per joint instead of per project.

 [Request a HeatCore AI quote or demo](https://www.therness.com/contact/?product=HeatCore%20AI)

**Therness solution:** [Welding monitoring system](https://www.therness.com/welding-monitoring-system/) — Each weld compared with a reference in the cycle, with anomaly flags and the ISO 3834 / ISO 17635 evidence kept per weld.

Written by **Luca Santoro**  , [founder](https://www.therness.com/author/luca-santoro/)

## Related Therness solution

[Thermography & NDT testingNon-contact anomaly screening and traceable thermal evidence for targeted follow-up NDT.](https://www.therness.com/thermography-ndt-testing/)

## Frequently Asked Questions

### What does EN 15085-5 cover?

It is the part of the EN 15085 series that deals with inspection, testing and documentation of welds on railway vehicles and components. It describes how the manufacturer plans inspection, which testing methods apply to which joints, and what records have to be kept so that the finished component can be shown to meet its requirements.

### How does EN 15085-5 differ from EN 15085-2?

The two parts answer different questions. EN 15085-2 is about the manufacturer: which certification level the company needs for the components it builds, and how that certification is obtained and maintained. EN 15085-5 is about the joints: how they are inspected and tested once production starts, and what evidence is kept. A certificate under part 2 is a precondition, not a substitute, for the inspection work described in part 5.

### What are the inspection classes in EN 15085-5?

Welds are grouped into inspection classes, running from the most demanding, tied to the highest safety relevance, down to classes where a visual examination is enough. The class of a weld decides the extent of testing: how much non-destructive testing is required, and how much of the production has to be covered. The class is a property of the joint, set at design stage, not something chosen after the weld is made.

### Which non-destructive methods does it rely on?

The familiar industrial set: visual examination, surface methods such as penetrant and magnetic particle testing, and volumetric methods such as radiography and ultrasonic testing, including phased array. Which one is acceptable depends on the joint geometry, the material and the type of imperfection the examination is meant to find.

### How long do the records have to be kept?

The documentation has to stay available for as long as the component is in service and can be audited. In practice that means the retention period is set by the operator or by the contract, and a fabricator that cannot reproduce the file for an old bogie or car body is exposed regardless of what the standard says on paper.

### Does process monitoring replace inspection?

No. Monitoring records how a weld was made; inspection establishes what state it is in. EN 15085-5 asks for evidence that the required examinations happened and that their results were accepted. Production data can strengthen the file by showing what each joint went through, but it does not remove the examination the class requires.

### Share this article

[LinkedIn](https://www.linkedin.com/sharing/share-offsite/?url=https%3A%2F%2Fwww.therness.com%2Fblog%2Fen-15085-5%2F) [X / Twitter](https://twitter.com/intent/tweet?url=https%3A%2F%2Fwww.therness.com%2Fblog%2Fen-15085-5%2F&text=EN%2015085-5%3A%20What%20Inspection%2C%20Testing%20and%20Documentation%20Must%20Prove) Email

## Related articles

![PAUT Weld Inspection Acceptance Criteria: How Rejects Get Decided](https://www.therness.com/assets/images/blog/paut-weld-inspection-acceptance-criteria-how-rejects-are-decided.jpg)

### PAUT Weld Inspection Acceptance Criteria: How Rejects Get Decided

PAUT weld inspection acceptance criteria explained: who sets them, amplitude versus sizing routes, what the scan file proves, and how to cut rejects.

[PAUT Weld Inspection Acceptance Criteria: How Rejects Get Decided](https://www.therness.com/blog/paut-weld-inspection-acceptance-criteria-how-rejects-are-decided/)

![EN 15085 Certification Levels CL1–CL4: What Auditors Check](https://www.therness.com/assets/images/blog/en-15085-railway-welding-certification-requirements-guide.webp)

### EN 15085 Certification Levels CL1–CL4: What Auditors Check

Which EN 15085 level each railway welding joint needs: CL1–CL4 by consequence of failure, the ISO 3834 part it forces, CP/CT classes, and what auditors check.

[EN 15085 Certification Levels CL1–CL4: What Auditors Check](https://www.therness.com/blog/en-15085-railway-welding-certification-requirements-guide/)

![Phased Array Ultrasonic Testing (PAUT) for Weld Inspection](https://www.therness.com/assets/images/blog/phased-array-ultrasonic-testing-paut-weld-inspection-guide.webp)

### Phased Array Ultrasonic Testing (PAUT) for Weld Inspection

PAUT weld inspection explained: probe setup, scan types, defect sizing, and acceptance criteria per ISO 17640 and ISO 13588. Practical B2B guide.

[Phased Array Ultrasonic Testing (PAUT) for Weld Inspection](https://www.therness.com/blog/phased-array-ultrasonic-testing-paut-weld-inspection-guide/)
