# Eddy current testing (ECT)

Source: https://www.therness.com/glossary/eddy-current-testing-ect/
Language: en

Welding glossary

Eddy current testing (ECT) is a non-destructive method in which a coil probe induces eddy currents in an electrically conductive part and the instrument reads how a discontinuity changes the probe's response. For welds, ISO 17643 applies it to surface-breaking and near-surface planar discontinuities, mainly in ferritic materials.

Full guide

[Eddy current testing: the long-form guide](https://www.therness.com/blog/eddy-current-testing-ect-welds-procedure-acceptance-criteria/)

This page defines the term. The guide works through how it is calculated, controlled and evidenced.

Eddy current testing passes an alternating current through a coil in a probe moved over the weld surface. The changing magnetic field induces eddy currents in the conductive metal beneath, and a discontinuity changes how those currents flow. The instrument shows the change as a signal that is evaluated on the complex plane, the analysis named in the title of ISO 17643:2015: “by complex-plane analysis”.

ISO 17643 defines the technique for surface-breaking and near-surface planar discontinuities, mainly in ferritic materials: weld metal, heat-affected zones and parent metal. It can also be specified for non-ferritic materials, for example in an application standard. It can be applied to coated and uncoated objects, in fabrication and in service. Testing is usually done in the as-welded condition, but very rough surface finishes can affect accuracy. Because the method reaches only the surface and the zone just beneath it, a flaw buried in the weld is a job for a volumetric method such as [phased array ultrasonic testing](https://www.therness.com/glossary/phased-array-ultrasonic-testing-paut/).

## Worked example: a trace you read, a signal you interpret

A weld toe on ferritic structural steel is examined twice for surface cracks.

- With [magnetic particle testing](https://www.therness.com/standards/iso-17638/), the examiner sees a trace of powder on the part, measures it and classes it as a [linear indication](https://www.therness.com/glossary/linear-indication/) or a non-linear one.
- With ECT, nothing is visible on the part. The probe scans the toe and the instrument displays a signal, which the operator evaluates on the instrument instead of reading it off the part.

Now ask the same question of an aluminium weld. Magnetic particle testing cannot be used there: it needs a magnetisable part, and ISO 23278, its acceptance-level standard, is written for ferromagnetic steel welds. ECT needs a conductive part, not a magnetisable one. ISO 17643 is written mainly for ferritic materials and says non-ferritic use can be specified, for example in an application standard. So on an aluminium weld ECT can be used when a specification calls for it.

Neither result describes how the weld was made. ECT reports the surface and near-surface condition at the moment of testing, and the parameters and thermal history behind the joint are a separate record.

## Where you meet this term

- Detection of surface-breaking and near-surface planar discontinuities in the weld metal, heat-affected zones and parent metal of ferritic steel, the case ISO 17643 is mainly written for
- Examination of coated or uncoated welds in fabrication and in service, both of which ISO 17643 names
- Welds in non-ferritic materials, when a specification such as an application standard calls for ECT
- NDT reports where the finding is an instrument signal, not a visible trace

## Related terms

[Phased array ultrasonic testing](https://www.therness.com/glossary/phased-array-ultrasonic-testing-paut/)

Phased array ultrasonic testing is a volumetric NDT method that fires a linear array of ultrasonic elements with programmable time delays to steer and focus the beam electronically, producing a sectorial image of a weld cross-section from a single probe position.

[Defect sizing](https://www.therness.com/glossary/defect-sizing-ndt/)

Defect sizing is the measurement of an indication's dimensions once non-destructive testing has detected it — principally its length along the weld and its height or through-wall extent — and different NDT methods measure these two dimensions with very different accuracy.

[Linear indication](https://www.therness.com/glossary/linear-indication/)

A linear indication is an indication whose length is greater than three times its width, as ISO 23278 defines it for magnetic particle testing of ferromagnetic steel welds; an indication whose length is less than or equal to three times its width is non-linear.

## Standards that use this term

- [ISO 17638](https://www.therness.com/standards/iso-17638/)Does ISO 17638 apply to your weld? Scope decision flow for the magnetic particle testing standard, the materials it excludes, and the records that support an MT inspection report.
- [ISO 9712](https://www.therness.com/standards/iso-9712/)Does ISO 9712 certify the person performing your examination? Scope decision flow for the NDT personnel standard, the roles it does not cover, and the records that survive an audit.

## Imperfections this term relates to

- [Longitudinal crack (ref. 101)](https://www.therness.com/defects/101-longitudinal-crack/)Cracks — ISO 6520-1 group 1.
- [Transverse crack (ref. 102)](https://www.therness.com/defects/102-transverse-crack/)Cracks — ISO 6520-1 group 1.

[All glossary terms](https://www.therness.com/glossary/)
